Nissan Sentra Owners Manual: Troubleshooting guide

Nissan Sentra Owners Manual / Pre-driving checks and adjustments / NISSAN Intelligent Key® (if so equipped) / Troubleshooting guide

Symptom		Possible Cause
When pushing the ignition switch to stop the engine	The P (Park) warning light in the instrument panel illuminates and the inside chime sounds continuously.	The shift lever is not in the P (Park) position.	Make sure that the shift lever is in the P (Park) position.
When placing the shift lever in the P (Park) position	The inside warning chime sounds continuously.	The ignition switch is in the ACC or ON position.	Place the ignition switch in the OFF position.
When opening the driver’s door	A warning chime sounds continuously.	The ignition switch is in the ACC position.	Place the ignition switch in the OFF position.
When pushing the door handle request switch to lock the door	The outside chime sounds for a few seconds.	The Intelligent Key is inside the trunk.	Be sure to carry the Intelligent Key with you.
		The Intelligent Key is inside the vehicle.	Be sure to carry the Intelligent Key with you.
		A door is not closed securely.	Close the door securely.
When closing the doors	The key warning light in the instrument panel blinks in yellow, the outside chime sounds 3 times and the inside warning chime sounds for approximately 3 seconds.	The ignition switch is in the ACC or ON position.	Place the ignition switch in the OFF position.
	The P (Park) warning light in the instrument panel illuminates and the outside chime sounds continuously.	The ignition switch is in the ACC or OFF position and the shift lever is not in the P (Park) position.	Make sure that the shift lever is in the P (Park) position and place the ignition switch in the OFF position.
	The outside chime sounds for approximately 3 seconds and all doors unlock.	The Intelligent Key is in the vehicle or trunk.	Be sure to carry the Intelligent Key with you.
When opening the driver’s door	A warning chime sounds continuously.	The ignition switch is in the ACC position.	Place the ignition switch in the OFF position.
When closing the trunk lid	The outside chime sounds for approximately 10 seconds and the trunk lid opens.	The Intelligent Key is inside the trunk.	Be sure to carry the Intelligent Key with you.
When pushing the ignition switch to start the engine	The key warning light in the instrument panel blinks in green.	The battery charge is low.	Replace the battery with a new one. See “Battery replacement” in the “Maintenance and do-it-yourself” section.
When pushing the LOCK button on the Intelligent Key to the lock the door	The outside chime sounds for a few seconds and all the doors unlock.	The Intelligent Key is inside the trunk.	Be sure to carry the Intelligent Key with you.
		The Intelligent Key is inside the vehicle.	Be sure to carry the Intelligent Key with you.
		A door is not closed securely.	Close the doors securely.

Warning signals

To help prevent the vehicle from moving unexpectedly by erroneous operation of the Intelligent Key or to help prevent the vehicle from being stolen, a chime or buzzer sounds from inside and outsid ...

Hood

Pull the hood lock release handle 1 located below the instrument panel until the hood springs up slightly. Locate the lever 2 in between the hood and grille and push the lever sideways ...

Other materials:

Rear power window motor
Removal and Installation REMOVAL Remove the rear door glass regulator (1). Refer to GW-21, "Removal and Installation" Remove the screws and the rear power window motor (2). INSTALLATION Installation is in the reverse order of removal. ...

System description
DESCRIPTION Engine Cooling System Schematic CVT Models Radiator Water inlet Reservoir tank Thermostat Engine oil cooler Thermostat housing Water pump Cylinder head Cylinder block Water control valve Water outlet Heater Electric throttle control actuator CVT oil wa ...

Main line between dlc and hvac circuit
Diagnosis procedure 1.Check harness continuity (open circuit) Turn the ignition switch off. Disconnect the battery cable from the negative terminal. Disconnect the following harness connectors. Ecm A/C auto amp. Check the continuity between the data link connector and the A/C ...