Nissan Sentra Service Manual: U0140 Lost communication (BCM)

Nissan Sentra Service Manual / Transmission & driveline / Transaxle & transmission / CVT: RE0F11A / U0140 Lost communication (BCM)

DTC Logic

DTC DETECTION LOGIC

DTC	CONSULT screen terms [Trouble diagnosis content]	DTC detection condition	Possible causes
U0140	LOST COMM (BCM) [Lost Communication With Body Control Module]	When the ignition switch is ON, TCM is unable to receive the CAN communications signal from BCM continuously for 2 seconds or more.	BCM Harness or connector (CAN communication line is open or shorted)

DTC CONFIRMATION PROCEDURE

1.PREPARATION BEFORE WORK

If another вЂњDTC CONFIRMATION PROCEDUREвЂќ occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

Start the engine and wait for at least 5 seconds.
Check the DTC.

Is вЂњU0140вЂќ detected? YES >> Go to TM-154, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

For the diagnosis procedure, refer to LAN-16, "Trouble Diagnosis Flow Chart".

U0141 LOST COMMUNICATION (BCM A)

DTC Logic

DTC DETECTION LOGIC

DTC	CONSULT screen terms [Trouble diagnosis content]	DTC detection condition	Possible causes
U0141	LOST COMM (BCM A) [Lost Communication With Body Control Module A]	When the ignition switch is turned ON, TCM continues no reception of the CAN communication signal from IPDM E/R for 2 seconds or more.	IPDM E/R Harness or connector (CAN communication line is open or shorted)

DTC CONFIRMATION PROCEDURE

1.PREPARATION BEFORE WORK

If another вЂњDTC CONFIRMATION PROCEDUREвЂќ occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

Start the engine and wait for at least 5 seconds.
Check the DTC.

Is вЂњU0141вЂќ detected? YES >> Go to TM-155, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

For the diagnosis procedure, refer to LAN-16, "Trouble Diagnosis Flow Chart".

DTC/Circuit diagnosis

U0073 COMMUNICATION BUS A OFF DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes U0073 COMM BU ...

U0155 Lost communication (IPC)

DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms [Trouble diagnosis content] DTC detection condition Possible causes U0155 LOST COMM (IPC) [Lost Communication ...

Other materials:

B0001, B0002 Driver airbag module
Description DTC B0001, B0002 DRIVER AIRBAG MODULE The driver air bag module is dual stage and is wired to the air bag diagnosis sensor unit through the spiral cable. The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the driver air bag module including t ...

B1430, B1432 Seat belt pre-tensioner LH
Description DTC B1430, B1432 SEAT BELT PRE-TENSIONER LH The seat belt pre-tensioner LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the seat belt pre-tensioner LH. PART LOCATION Refer to SRC-5, " ...

Dtc/circuit diagnosis
U1000 can comm circuit Description Refer to LAN-7, "CAN COMMUNICATION SYSTEM : System Description". Dtc logic DTC DETECTION LOGIC NOTE: U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm that there are actual CAN diagnostic sym ...